ISOJOINT®

IsoJoint® is a true monolithic isolating joint. The most up-to-date, patented joint on the market,  IsoJoint® does not depend on the use of isolating sleeves and washers for bolts nor isolating gaskets or O-rings between flanges.

Why?

These isolating gasket kits require a critical, even surface and proper placement of a sealing element to provide regular and variable crushing and must be maintained over the life of the isolator. External pressure causing an uneven load on the flange area can result in loss of isolating properties as well as the transported fluid.

Reduce Maintenance Time & Costs

IsoJoint® employs one or more, preassembled pressure seals and the isolating rings.

Unlike isolating gasket kits, IsoJoint® does not depend on installer’s actual fitting of the joint’s isolating gasket, sleeves and washers and the possible loss or damage to any one of the number of these materials which would result in complete breakdown of the isolated flange. One lost or damaged part will render these flanges useless.

The monobloc design of the IsoJoint® allows the joint to be welded into place as one piece virtually eliminating any field problems. Unless a meticulous on-site assembly and overwrapping is undertaken in the installation of the isolating gasket kits, gradual penetration of moisture will erode the electrical resistance. This problem, along with the others listed above, makes inspection and maintenance necessary. Contrary to this inconvenience, IsoJoint’s® technique and design of the pressure seals coupled with the closure weld guarantees that the specified mechanical and electrical properties will always be maintained allowing for direct burial and requiring no maintenance.

Be More Productive

At first glance, flange gasket kits seem to be the economical route to take to the isolating problem, but when coupled with the expense of components, labor and maintenance, IsoJoint® has proven itself to be the productive solution. The IsoJoint® provides for current control by separating pipework into distinct zones as part of a cathodic protection system and effectively eliminating long-line currents. This assures increased plant and equipment life by reducing or eliminating corrosion damage.

Effective control can be realized by placing IsoJoints® at pipeline entry points to processing plants or gas compressor stations where a branch is connected to the mainline, where two pipelines of different material connect to where well-coated pipe meets a poorly coated system. Optimum cathodic protection can be achieved for each section of pipeline—maximizing savings and minimizing costs.

Isojoint diagram

Advantages

IsoJoints® are manufactured in accordance with the highest technical standards which guarantee mechanical requirements (torque, traction, bending, etc.) are met for the specific needs of a plant. Full Technical details should be supplied.

  • Specific hydraulic internal pressures are maintained.

  • Isolating requirements are met and surpassed in regard to the electrical characteristics of the product carried in the pipeline.

  • IsoJoints are designed according to ASME VIII, Division I

  • Earthquake resistant – Acts as a thrust block or joint.

  • All coatings are applied in-house. Standard joints are coated internally and externally with epoxy-resin coatings. Different standards as per customer’s requirements. NSF approved internal coating is available.

  • All testing is done in-house. Hydrostatic and electrical are standard. Ultrasonic, X-ray and dye penetrant testing can be done if requested. Testing voltage 3,000 v-50 Hz. Electrical resistance -5 Mohm minimum. Test Pressure: 1.5 time working pressure. Working temperature up to 160 °F. Customers may require special test values.

Common Applications

  • Existing and new construction

  • Gas, Oil, Liquid Petrochemical and Water Lines

  • Before and from gas distribution lines

  • On gas or liquid fuel tanks

  • Under or over ground usage

  • Riser connections on platform

  • Existing and new construction

  • Gas, Oil, Liquid Petrochemical and Water Lines

  • Before and from gas distribution lines

  • On gas or liquid fuel tanks

  • Under or over ground usage

  • Riser connections on platform

Monolithic isolating joints, 1/2″ to 150″ diameter, ANSI 150# to 2500# and up to 10,000#, Gr. B to X70.
U.S. Patented • Manufactured to ISO 9001:2008

Call Us

We’re just a phone call away

Email Us

Send us a message anytime

Signup for Our Newsletter